How to Make a Glass Bottle Hummingbird Feeder
How to Make a Glass Bottle Hummingbird Feeder
Relieve coin while attracting hummingbirds by creating this homemade hummingbird feeder from a glass canteen and some copper wire.
Forget ownership expensive, decorative sugar-water feeders. At present y'all can make your own bootleg hummingbird feeder for merely a few bucks using a recycled canteen and copper accents, 1 that is a decorative add-on to any backyard. You'll be amazed at how fun and easy it is to make this one-of-a-kind craft idea. Y'all'll be attracting hummingbirds to this feeder before you know it!
Materials
- 5 feet of 4-gauge untreated copper wire
- 3 to 5 feet of 12-gauge untreated copper wire
- Chaplet or other decorations
- D ring or carabiner
- Spiral eye
- File
- Needle-nose pliers
- Wire cutter
- Hummingbird feeding tube – Find these at bird supply stores and online. If you tin can't find a local supplier, effort doing a web search for "hummingbird feeding tubes" to discover a source.
- Drinking glass Bottle (Note: Glass bottles larger than 375 ml are heavy and more prone to leakage. Thus, they are not recommended for this projection. Above all, the canteen must provide a tight fit for the stopper portion of the feeding tube you purchase. Anything less than an closed fit volition allow the nectar to baste from the feeding tube. Many soda and water bottles are a good fit for a commercial tube feeder assembly. Exist sure to test the seal before you lot complete your design and add together sugar water.)
Instructions
Step 1
File the ends of the copper wires so there are no abrupt edges.
Take the iv-estimate wire and bend it at one of the ends to form a small circle. This should fit loosely over the opening of the bottle.
Insert the bottle in the circumvolve, and make 1 more loop around the neck to hold it deeply.
Step two
With the neck of the bottle securely in the ii loops, air current the balance of the wire around the bottle. This is where you lot accept a little freedom to create your own design. The wire should be loose enough to easily remove the bottle for refilling the sugar water, but tight plenty to hold the feeder deeply.
Bend the last 18 inches or then of wire upward to brand a hanging hook and and then fashion a loop at the very end to secure it, equally shown.
Step three
Next, decorate your feeder using the 12-gauge copper wire. Use needle-nose pliers and wire cutters to shape the wire every bit needed. Here's a design tip: To create the wait of curling vines, wrap the wire effectually a pencil first and so adhere it in pieces.
Use colorful chaplet or other adornments to complete your design. Remember, hummingbirds dear red, and then information technology's a neat accent color.
Step 4
Remove the canteen and fill up information technology with carbohydrate water. Then have your store-bought feeding tube and gently twist the stopper into place at the opening of the canteen. Information technology should fit snugly to avoid leaking.
After you make full it with saccharide water, identify the bottle back into the copper holder. You might have to milkshake the bottle a little to dislodge any air bubbles. If information technology leaks, remove the feeding tube and endeavour repositioning the stopper to get a more snug fit.
Set up to put your feeder to work? Brand sure it hangs securely past hooking the feeder onto a snap ring or carabiner. So put the band through a screw center and hang the unabridged feeder in the desired location.
Beyond Feeders: 5 More Ways to Attract Hummingbirds
See more from Birds & Blooms here.
Originally Published: April 12, 2019
Source: https://www.familyhandyman.com/article/how-to-make-a-glass-bottle-hummingbird-feeder/
0 Response to "How to Make a Glass Bottle Hummingbird Feeder"
Post a Comment